Casing and tubing running services companies ensure quality steel pipe installation by following a strict set of guidelines and procedures. First, they inspect the pipe for any defects or damage before installation. This includes checking for any corrosion, dents, or other irregularities. They also check the pipe for any signs of wear or fatigue.
Once the pipe is deemed suitable for installation, the casing and tubing running services Company will then use specialized tools and equipment to ensure a secure and safe installation. This includes using a torque wrench to ensure the pipe is properly tightened and secured. They will also use a pipe cutter to ensure the pipe is cut to the correct Length and Diameter.
The casing and tubing running services company will also use a variety of other tools and equipment to ensure the pipe is properly installed. This includes using a pipe bender to ensure the pipe is bent to the correct angle and shape. They will also use a pipe Threader to ensure the threads are properly cut and Sealed.
Labels a
Calculated Mass c
Nominal Linear Mass T& C b,c
Wall Thick- ness
em, Mass Gain or Loss Due to End Finishing d
Outside Diameter
Inside Diameter
Drift Diameter
Plain- end
kg
Round Thread
Buttress Thread
wpe
D
kg/m
t
D
mm
kg/m
Short
Long
RC
SCC
mm
mm
mm
1
2
3
4
5
6
7
8
9
10
11
12
13 3/8
48
339.72
71.43
8.38
322.96
318.99
68.48
15.04
—
— 17.91
—
13 3/8
54.5
339.72
81.1
9.65
320.42
316.45
78.55
13.88
—
16.44
—
13 3/8
61
339.72
90.78
10.92
317.88
313.91
88.55
12.74
—
14.97
—
13 3/8
68
339.72
101.19
12.19
315.34
311.37
98.46
11.61
—
14.97
—
13 3/8
68
339.72
101.19
12.19
315.34
311.37
98.46
11.67 f
—
14.33
—
13 3/8
72
339.72
107.15
13.06
313.6
311.15 e
105.21
10.98
—
13.98
—
13 3/8
72
339.72
107.15
13.06
313.6
311.15 e 309.63 309.63
105.21
10.91 f
—
14.33
—
13 3/8
72
339.72
107.15
13.06
313.6
105.21
10.98
—
13.98
—
13 3/8
72
339.72
107.15
13.06
313.6
105.21
10.91 e
—
—
16
65
406.4
96.73
9.53
387.4
382.57
96.73
18.59
—
— 20.13
—
16
75
406.4
111.61
11.13
384.1
379.37
108.49
16.66
—
18.11
—
16
84
406.4
125.01
12.57
381.3
376.48
122.09
14.92
—
—
—
16
109
406.4
162.21
16.66
373.1
368.3
160.13
—
—
—
18 5/8
87.5
473.08
130.21
11.05
450.98
446.22
125.91
33.6
—
39.25
—
20
94
508
139.89
11.13
485.7
480.97
136.38
20.5
27.11
24.78
—
20
94
508
139.89
11.13
485.7
480.97
136.38
20.61
27.26 g 24.27 17.84
24.78
—
20
106.5
508
158.49
12.7
482.6
477.82
155.13
18.22
22
—
20
133
508
197.93
16.13
475.7
470.97
195.66
13.03
16.02
—
NOTE See also Figures D.1, D.2, and D.3.
a Labels are for information and assistance in ordering.
b Nominal linear masses, threaded and coupled (Column 4) are shown for information only.
c The densities of martensitic chromium steels (l80 Types 9Cr and 13Cr) are less than tHose of Carbon steels; The masses shown are therefore not accurate for martensitic chromium steels; A mass correction factor of 0.989 shall be used.
d Mass gain or loss due to end finishing; See 8.5.
e Drift diameter for most common bit size; This drift diameter shall be specified in the purchase agreement and marked on the pipe; See 8.10 for drift requirements.
f Based on 758 mPa minimum yield strength or greater.
g Based on 379 mPa minimum yield strength.
Finally, the casing and tubing running services company will use a variety of testing methods to ensure the pipe is properly installed. This includes pressure testing, Hydrostatic testing, and other tests to ensure the pipe is safe and secure. By following these guidelines and procedures, casing and tubing running services companies can ensure quality steel pipe installation.
Oil Tubechinesehigh–gradewholesaler,Casing Pipechinagood company,
Once the pipe is deemed suitable for installation, the casing and tubing running services Company will then use specialized tools and equipment to ensure a secure and safe installation. This includes using a torque wrench to ensure the pipe is properly tightened and secured. They will also use a pipe cutter to ensure the pipe is cut to the correct Length and Diameter.
